|
Owners Manual
- Covers the Buddy 50, 125, 150 and 170i
- We have a couple of older ones left that only go up to the 150 (as
shown in the picture)
- If you need one for the 170i just add a note in the order and we'll
make sure you get the correct one
|
$ 15.00
|
|
Service Manual
- Essential if you are going to tackle anything other than basic
maintenance on your scooter
- There is no manual available for purchase for the Buddy 170i. Sorry
|
$ 32.00
|
|
Air Filter
|
$12.72
|
|
Air Filter
|
$15.50
|
|
Oil Filter
- Buddy 125 - 150 - 170 - Hooligan - Blur
- This is an aftermarket HiFlo Filter
- Has a "slot" to tighten with a large screwdriver
- OEM version has a "nut" to tighten with a wrench
|
$8.99
|
|
Oil Filter Kit
- Includes Oil Filter, O-Rings, and Crush (Sealing) Washer that should be replaced when changing your engine oil
- Crush Washer = Drain Plug
- O-Rings = Oil Screen Cover and Dipstick
|
$14.99
|
|
Fuel Filter
- Includes fuel filter and rubber mounting strap
- Buddy 125 - 150
|
$8.56
|
|
Oil Screen
|
$4.02
|
|
Spark Plug - NGK
- NGK is the standard in motorcycle spark plugs and stock on your Genuine Scooter
- Fits the Buddy 50 and Roughhouse 50
- BP7HS
|
$3.50
|
|
Spark Plug - NGK
- NGK is the standard in motorcycle spark plugs and stock on your Genuine Scooter
- Fits the Buddy 125, 150, 170i and Hooligan 170i
- CR7HSA
|
$3.99
|
|
Spark Plug - NGK
- NGK spark plugs are recommend by Genuine USA and PGO Scooters
- Fits the Buddy Kick
- CR7E
|
$7.50
|
|
Engine Oil Dipstick
- Fits the Buddy 125, 150 and 170i
- Includes new o-ring
|
$ 9.54
|
|
Gas Cap - Metal
- Gas cap for the Metal Tank Buddy's 2007 and newer
- Includes new gasket
- Fits all 50, 125, and 150's
- Sometimes referred to as the Iron Tank models
|
$ 19.54
|
|
Gas Cap - Plastic
- Cap for the Plastick Gas Tank 2006 Buddy's
- Fits the 50 and any other 2006 plastic tank Buddys
|
$ 9.54
|
|
Speedometer Cable
|
$15.60
|
|
Speedometer Cable
- Buddy 125 - 2006 AND OLDER ONLY
|
$11.22
|
|
Rear Brake Cable
|
$19.08
|
|
Rear Brake Cable
|
$19.08
|
|
Throttle Cable
|
$25.20
|
|
Throttle Cable
|
$23.52
|
|
Belt
|
$34.95
|
|
Belt
- Buddy 125 - 150 -170
- Stock Belt
|
$48.80
|
|
Gasket - Belt / CVT Cover
|
$7.80
|
|
Key Blank
|
$6.36
|
|
Ignition Switch Assembly
- Complete ignition switch assembly with 2 keys
- This switch is used for the ignition as well as the seat latch
and the steering lock
- Fits: Buddy 125 and 150 all years
- Fits: Buddy 50 manufactured Nov 2012 or older
|
$99.00
|
|
Ignition Switch Assembly
- Fits Buddy 50's manufactured Dec 2012 and later
|
$ 99.00
|
|
Ignition Switch
- Complete Assembly and 2 Keys
- Buddy 170i
|
$93.00
|
|
Right Hand Switch Assembly
- Complete switch assy for the Buddy 50, 125, 150 and 170i
- 2007 models and newer with Hazard Switch
- If you need one for a 2006 model give us a call
|
$51.30
|
|
USB Port
- The newest Genuine Scooters are coming equipped with a USB port
instead of the 12v accessory plug
- You can retrofit this USB Plug to your older Genuine Scooter
|
$ 34.99
|
|
Floormat - Black
- Help your Buddy look its best......replace that faded or worn out floormat
- Most Buddy 125's
|
$34.80
|
|
Floormat - Green
- Buddy 50 and 150 Italia - International Series
|
$34.80
|
|
Floormat - Brown
- Buddy 50 and 150 Pamplona - International
|
$34.80
|
|
Battery Cover - Black
- Fits all Buddy's (50, 125, 150 and 170)
|
$ 10.32
|
|
Headlight Assembly
- Large Version
- Includes both bulbs, wiring sub harness, and rubber cap
- Fits ALL Buddy's 2007 and newer
|
$90.00
|
|
Handlebar Cover - Upper
- Fits Buddy 50, 125, 150 and 170i
- We only stock a few colors
- If your color is not in stock it will ship in 4-6 business days
- We will be stocking more bodywork soon, in the meantime give
us a call to order anything you don't see
|
$89.80
|
|
Headlight Ring (Bezel)
- Large chrome version for 2007 and newer models
- Fits: Buddy 50, 125, 150 and 170
- Also available in black
|
$39.35
|
|
Headlight Ring (Bezel) - Flat Black
- Black version of the above - 2007 and newer
- Fits: Buddy 50, 125, 150 and 170
- Used on the Psycho and other versions
|
$39.78
|
|
Small Headlight
- Fits 2006 Buddy's ONLY
- Complete assembly
|
$31.00
|
|
Headlight Ring (Bezel) - Small
- Used on 2006 models only
- Buddy 50, 125, and 150
- Available in chrome only
|
$19.06
|
|
Grip Assy - Right Hand - Italia
/ St. Tropez
- Buddy 50, 150 and 170i International Series - Italia / St. Tropez
- Includes Throttle Tube
- The grip is GREY (it may seem a little green in the picture but its just the lighting) It is the orginal color that came on those two "International Series"
- Will fit all Buddys, if you'd like to change out your original grips
- Don't forget the Grip Glue (just below the all the grips)
|
$10.34
|
|
Grip - Left Hand - Italia
/ St. Tropez
- Buddy 50, 150 and 170i International Series - Italia / St. Tropez
- The grip is GREY (it may seem a little green in the picture but its just the lighting) It is the orginal color that came on those two "International Series"
- Will fit all Buddys, if you'd like to change out your original grips
|
$8.04
|
|
Grip - Right Hand - Black
- Fits: All Buddys and Black Cat
- Includes throttle tube
- Don't forget the Grip Glue (just below the all the grips)
|
$10.34
|
|
Grip Left Hand - Black
- Fits: All Buddys and Black Cat
|
$8.04
|
|
Grip - Right Hand - Brown
- Will fit all Buddys if you'd like to change out your original grips
- Includes throttle tube
|
$10.34
|
|
Grip - Left Hand - Brown
- Will fit all Buddys if you'd like to change out your original grips
- Don't forget the Grip Glue (just below the all the grips)
|
$8.04
|
|
Grip - Right Hand - Tan
- Originally used on Pamplona International Series Buddys
- Will fit all Buddys if you'd like to change out your original grips
- Includes throttle tube
|
$10.34
|
|
Grip - Left Hand - Tan
- Originally used on the Pamplona International Series
- Will fit all Buddys if you'd like to change out your original grips
- Don't forget the Grip Glue (just below the all the grips)
|
$8.04
|
|
Grip - Right Hand - White
- Was used on the Pink Buddys and possibly others?
- Will fit all Buddys if you'd like to change out your original grip
- Includes throttle tube
|
$10.34
|
|
Grip - Left Hand - White
- Will fit all Buddys if you'd like to change out your original grips
|
$8.04
|
|
Grip Glue
- Small tube of grip glue
- Good for 1 - 2 sets of grips
- Makes installation of new grips easier and keeps them from spinning
|
$2.50
|
|
Brake Lever - Front (RH)
- Buddy 50 - 125 - 150 -170
|
$15.12
|
|
Brake Lever - Rear (LH)
- Buddy 50 - 125 - 150 - 170
|
$12.72
|
|
Pivot Bolt
- Pivot bolt for the Left / Rear lever only (other side coming soon)
- BC
|
$ 1.00
|
|
Muffler Cover - Heat Shield
- Muffler heat shield - Black Plastic
- Does NOT include any bolts, spacers, or washers (we now have them for sale online!)
- Buddy 50, 150 and 170
- 3 Mounting Holes
|
$19.08
|
|
Muffler Cover - Chrome
- Muffler Cover / Heat Shield - Includes aluminized backing
- Chromed steel
- Buddy 125 Only
- 2 Mounting Holes
|
$ 33.80
|
|
Mounting Hardware - Heat Shields
- Sold as a "kit" as seen in the picture
- 1 "kit" includes 1 each of the following: Heat Resistant Washer, Grommet, Cup Washer, and Screw
|
$ 4.38
|
|
Speedometer Drive Gear
- Used to drive your speedometer cable off the front wheel
- Buddy 50
|
$ 37.70
|
|
Starter Motor
- Fits: Buddy 50, RoughHouse50, Rattler 50, and Black Cat 50
|
$117.00
|
|
Starter Motor
- Fits: Buddy 125, 150, 170 and Hooligan
|
$173.80
|
|
Magneto Assembly
- Complete assembly with stator and rotor
- Fits: Buddy 50
|
$127.20
|
|
Magneto Assembly
- Complete assembly with stator and rotor
- Fits: Buddy 125
|
$122.00
|
|
CDI
- AKA "The Black Box"
- Controls the ignition of your scooter
- If you have lost spark completely this is most likely the cause (however, a proper troubleshooting should be completed per the service manual)
- Includes CDI unit and rubber strap/mount
- Buddy 125 - 150
|
$60.00
|
|
Ignition Coil
- Buddy 50
- Includes Coil, Wire, and Spark Plug Cap
|
$43.20
|
|
Coil
- Buddy 125 and 150
- Includes Coil, Wire, and Spark Plug Cap
- Has a 45 degree angled cap
|
$45.00
|
|
Coil
- Buddy 170i
- Includes Coil, Wire, Mounting Bracket, Sub-Harness, and
Spark Plug Cap
|
$50.00
|
|
Ignition Coil
- Fits the NEW Buddy Kick
- Includes Coil, Wire, and Cap
|
$ 59.00
|
|
Regulator / Rectifier
- If your scooter is not charging the battery while running this could be your problem (troubleshoot per the service manual)
- Buddy 50 - 125 - 150
|
$36.00
|
|
Starter Relay / Solenoid
- If your engine will not turn over at all and your battery tests OK this could be your issue (troubleshoot properly)
- Includes relay and rubber strap/mount
- Buddy 125 - 150 - 170
|
$31.80
|
|
Starter Relay
- If your engine will not turn over at all and your battery tests OK this could be your issue (troubleshoot properly)
- Includes relay and rubber strap/mount
- Buddy 50
|
$26.34
|
|
Horn Relay
- Used on the Buddy 150
- If your Stebel Air Horn is not working, check this first
|
$15.00
|
|
Brake Light Switch - Front (RH)
- Buddy 50 - 125 - 150 - 170
- Activates your brake light and allows the scooter to start
|
$8.04
|
|
Brake Light Switch - Rear (LH)
- Buddy 50 - 125 - 150 - 170
- Activates your brake light and allows the scooter to start
|
$4.80
|
|
Turn Signal - Front
- Buddy 50 - 125 - 150 - 170
- Choose Left or Right from menu ------->
- Sides are always as if you were sitting on your bike
- These are the "handlebar" turn signals as required by the USA DOT, may not be installed on all versions of the Buddy
|
$31.20
|
|
Turn Signals - Rear
- Buddy 50 - 125 - 150 - 170
- Sold in pairs only now
|
$48.00
|
|
Turn Signal Lens - Front
- All Buddy's - 50 - 125 - 150 - 170
- Lens ONLY
- Choose Side -------->
- Sold each
|
$9.19
|
|
Turn Signal Bulb - Front
- All Buddy's: 50 - 125 - 150 - 170
- Amber Bulb ONLY
- Sold each
|
$3.32
|
|
Turn Signal Lens - Front Cover
- Turn signal lens for the turn signals that are integrated into the front bodywork
- Genuine is only selling them in pairs now. However we do have some right sides still in stock. You can order a right side only, or if you need a left side you will need to order the pair. Thanks
|
|
|
Rear Tail / Brake Light - LED
- Tail light assemblly for all Buddy's
- LED version as used on 2008 and newer models
- Will work on older, non LED versions as well
|
$106.25
|
|
Mirror Set - Short
- Short (8") stem version - Chrome
- Stock on pre-2009(?) models (Buddy 50, 125, 150 and 170)
- Will work on all Buddy models
- 8mm threads - 1 regular - 1 reverse
|
$39.00
|
|
Mirror Set - Long
- Long 10 inch stem version - Chrome
- Used on newer Buddy models (50, 125, 150, and 170)
- Will work on old or new models
- 8mm threads - 1 regular -1 reverse
|
$56.80
|
|
Mirror Set - Black
- Same as the long 10" version above in flat (matte) black
- Will work on ALL Buddys
- 8mm threads - 1 regular - 1 reverse
|
$56.80
|
|
Brake Pads
- Front
- Buddy 50 front brake pads
|
$29.93
|
|
Brake Shoes
- Rear
- Buddy 50 rear brake shoes
|
$29.55
|
|
Brake Pads - Front
|
$34.80
|
|
Brake Shoes - Rear
|
$35.32
|
|
Roller Weights
- Buddy 50, RoughHouse 50, Rattler 50
- Used in the Variometer and wear over time
- 16mm x 13mm
- Stock 7.5 grams
- Sold as a set of 6
|
$14.40 / Set (6)
|
|
Slide Pieces
- Variator component
- Sold as a set of 3
- Buddy 125 - 150
|
$2.76
|
|
Clutch Shoe Assembly
- Buddy 50
- Another wear item in your driveline
- Comes complete and pre-assembled as shown
|
$88.00
|
|
Generator/Magneto Fan
- Buddy 50
- Located on the right side of engine
- Keeps air flowing over your engine to keep it cool
|
$16.10
|
|
Valve Cover Gasket (O-Ring)
|
$3.88
|
|
Oil Tank Cap
|
$2.00
|
|
Piston - Buddy 50
- This is an updated piston that will work on all years
|
$24.00
|
|
Ring Set - Piston
- Buddy 50
- Sold as a set of two (2)
|
$17.52
|
|
Piston Pin (Wrist Pin) |
$5.20
|
|
Bearing (Small End)
- Buddy 50
- Bearing between crankshaft and wrist pin
|
$19.92
|
|
Circlips - Wrist Pin
- Buddy 50
- A good rule of thumb is - anytime you see these circlips you should replace them (even if you are just replacing your piston rings)
|
$1.30
|
|
Head Gasket - Buddy 50
- At this price, there's no reason not to replace it when you are doing a rebuild
|
$3.00
|
|
Base Gasket
|
$3.18
|
|
Exhaust Gasket
- Fits between cylinder head and muffler assy
- Buddy 125
|
$2.00
|
|
Top End Rebuild Kit
- Includes everything you need to freshen up your Buddy 50
- Includes: Cylinder, Cylinder Head, Piston, Ring Set, Wristpin and Bearing, Circlips, Gaskets and Studs
- Will work on all Buddy 50's
|
$179.00
|
|
Cam Chain Tensioner
- Tensioner with new o-ring and bolt
- Fits Buddy 125
|
$22.80
|
|
Cam Chain Tensioner
- Tensioner only
- Fits Buddy 150, 170i, and Hooligan 170
|
$16.80
|
|
Kickstart Lever - Buddy 50
- Does NOT include pinch bolt
|
$18.40
|
|
Kickstart Spring
- Part of the kickstart mechanism that can wear out
- Fits: Buddy 50
|
$19.50
|
|
Kickstart Ratchet
- Engages inside the belt cover to turn over the engine
- Buddy 125 - 150
|
$4.23
|
|
C-Ring - Kickstart
- Holds kickstart shaft in place on backside of belt cover.
- Buddy 125 - 150
|
$1.30
|
|
Side Stand
|
$ 13.56
|
|
Side Stand Spring
- Used on ALL Buddy Scooters
|
$ 2.22
|
|
Centerstand Rubber Bump Stop
- If you hear a loud "clang" when you put your centerstand up check to see if this is missing
- Buddy 50
|
$ 1.52
|
|
Centerstand Spring
|
$ 2.21
|
|
Fuel Level Sender - "Iron Tank"
- Fits 2008 and newer Buddys with a steel gas tank (Iron Tank)
- All models - 50, 125, 150 and 170
- Includes new gasket
|
$ 25.74
|
|
Fuel Petcock (Autocock)
- Vacuum operated fuel sending unit
- This unit allows the fuel to flow from your gas tank to carburetor
- Includes filter screen
- Buddy 50 - 125 - 150
|
$22.08
|
|
O-Ring - Float Bowl
- New float bowl o-ring
- Its good to have one on hand anytime you are going to crack open the carburetor for cleaning or re-jetting
- Fits Buddy 125 - 150
|
$1.83
|
|
Float
- Buddy 125, Buddy 150 and Blur 150
|
$5.95
|
|
Float Needle
- Keeps the carb from overflowing - can wear out over time
- Buddy 125 - 150
|
$7.20
|
|
Idle Jet (Slow Jet)
- Buddy 125 - 150
- #38 is the stock size
- #40 and #42 may provide a more steady idle or if you have any
performance modifications on your scooter
|
$4.99
|
|
Accelerator Pump Diaphragm
|
$18.00
|
|
Spring (Accelerator Pump)
|
$1.30
|
|
Rubber Boot (Accelerator Pump)
|
$1.98
|
|
Float Bowl Screw - 93500040121H
- Float Bowl Screw - Silver
- Part Number: 93500040121H
- Check the parts manuals to see where it is used
- If you're taking your float bowl off you'll want to have some on hand
- 4 x 12 machine screw
|
$ 1.20
|
|
Carburetor Assembly
- Complete assembly with auto choke etc
- Fits: Buddy 125 and 150
|
$254.99
|
|
Slide / Diaphragm
- Sometimes the rubber diaphragm can become damaged if it does
your scooter will most likely not accelerate past a certain speed
- Fits the Buddy 125
|
$38.40
|
|
Float Bowl O-Ring
- Now available without having to buy the complete float bowl assy
- If you're taking the float bowl off to clean the carb or re-jet its a good idea to have one of these on hand
- Buddy 50
|
$ 2.08
|
|
Float Bowl + O-Ring
- Fits Buddy 50
- Includes Float Bowl, O-Ring and Drain Screw
|
$39.60
|
|
Float
|
$32.00
|
|
Float Pin
|
$.99
|
|
Float Needle
|
$7.15
|
|
Intake O-Ring
- Fits between carburetor and cylinder
- Buddy 50 and Rattler 110
|
$.99
|
|
Intake O-Ring
- Fits on the spacer between the intake manifold and the cylinder head
- If your scooter "hunts" for an idle, or dies unexpectedly, check this o-ring
- Fits the Buddy 125 and Buddy 150 (also the Blur 150)
|
$ 2.50
|
|
Main Jet
|
$4.27
|
|
Mixture Screw Assy
- Complete mixture screw assembly
- Includes screw, spring, washer and o-ring
- Fits: Buddy 50 and Rattler 110
|
$5.50
|
|
Autobystarter - Buddy 50
- Also known as the Auto Choke Assembly
- Includes o-rings
|
$91.00
|
|
Screw - 90110401200
- Common screw used throughout all Genuine scooters
- Part number is: 90110401200
- Check the parts manuals to see where it is used
- 4 x 12 self tapping screw - Black
|
$ 1.16
|
|
Screw - 90150501601
- Tapping screw used on multiple modes
- Part Number: 90150501601
- Check the parts manuals to see where it is used
- 5 x 12 tapping screw
|
$ .86
|
|
Screw - 90130501401
- Used to secure the battery cover on the Buddys
- Part Number: 90130501401
- Check the parts manuals to see where it is used
- 5 x 14 tapping screw
|
$ .50
|
|
Screw - 90110401600
- Tapping screw used on multiple models - Gold
- Part Number: 90110401600
- Check the parts manuals to see where it is used
- 5 x 16 tapping screw
|
$ 1.20
|
|
Flange Bolt - 90190804003
- 8 x 40 flange bolt used in multiple places
- Check the parts manuals to see where it is used
- Part Number: 90190804003
|
$ 2.80
|
|
Flange Bolt - 90191002800
- 10 x 28 x 1.25 fine thread
- Check the parts manuals to see where it is used
- Part Number: 90191002800
|
$ 1.88
|
|
Flange Nut - 92060800002
- 8 x 1.25 flange nut
- Has Blue Loctite pre applied
- Check the parts manuals to see where it is used
- Part Number: 92060800002
|
$ .92
|
|
Flat Washer - 92140600018
- 6 x 13 x 1 Plain Washer
- Check the parts manuals to see where it is used
- Part Number: 92140600018
|
$ .92
|
|
O-Ring - 95512000001
- Check the parts manuals to see where it is used
- Part Number: 95512000001
|
$ 1.70
|
|
O-Ring - 95511300001
- Check the parts manuals to see where it is used
- Part Number: 95511300001
|
$ 1.70
|